Blazer
Page 1 of 3 123 LastLast
Results 1 to 20 of 53

Thread: ARB Hilux

  1. #1
    Join Date
    Jul 2013
    Location
    Vitoria , Spain
    Posts
    128

    Default Maxi-pro Hilux Truggy RcModelEX

    !Hi !
    this is my new project .
    Trailfinder body
    modelex chasis
    gelande 2 wheel
    proline super swamper
    combo robitronic 21.5 sensor
    gmade piggyback shock regulable
    The other part come in a few days...





    Today the body meets chasis....





    Now waiting for more parts...
    today lights.. only with led 4 . For not more cables and holes for cables...



    today work , mount links and axles greased and xvc converted , hpi unit with motor and suspension gmade piggyback...
    for tomorrow mirrors ultimate rear suspension adjust






    Last mods...






    Thanks !





    Last edited by FREEDOM83; 07-28-2014 at 08:01 AM.
    I DRIVE, HE GUIDE ME

    -FOOTBALL +RACES

    http://euskoscalecrawler.foroactivo.com/

  2. #2
    Join Date
    Jul 2013
    Location
    Vitoria , Spain
    Posts
    128

    Default

    Then I saw who was walking tricycles and insitu clearing and initially thought it was the pin rim mkrarlo but saw that it was good inside .... I is successfully broken the bearing pin ....
    remove the entire shaft and opening saw this:



    was all mounted right just gave too shift from emi and seems to heal him to turn over the account pulled the bearing out ... nothing less than 1mm but slowly over 8 hours of use that will have you see the result ....
    I initially ... I put the bearings of series and continue with the route but at the end of bearing take full group holding the same side of the shield was shattered miss ... neither will we no picture ... hehehehe
    nothing this morning I went for bearings here to shop Arizti bearings and good 3 euros each but I have caught pa is a special measure and was not valian which already had before ....



    and you see in the picture what today has come to me .... a trail rider rc4wd love handles and also rc4wd led bar ... asked all rcbitz .... this afternoon I have more work ... jejejee and this week also came innerspring cushions for back ... by the way on Saturday in the 15 minutes I could walk and test the spring issue and do not want to remove them ... just make a couple of adjustments ...

    Yesterday I started assembling the bearings of series and take to regrease and resets everything better
    and this morning I put the wheels ....
    First narrow blue rings rc4wd to put the swamper proline



    and after a few hours of work ..



    I have also left the bar LED placed



    and here with Their tires



    LIGHT TEST



    This afternoon mess! Yeah!


    !Mounted !




    LITTLE ACCIDENT...
    I DRIVE, HE GUIDE ME

    -FOOTBALL +RACES

    http://euskoscalecrawler.foroactivo.com/

  3. #3
    Join Date
    Jul 2013
    Location
    Vitoria , Spain
    Posts
    128

    Default

    Now yess . Finished for the moment...

    Pitbull growler 1.55 arrived !

    comparision with swampers

    Here the rims for view why i can mount 1.55 tire in 1.9 rims

    mounted

    Hilux finished with new tires and new rubber mudflaps



    little boy repair and new color for hilux...



    I DRIVE, HE GUIDE ME

    -FOOTBALL +RACES

    http://euskoscalecrawler.foroactivo.com/

  4. #4
    Join Date
    Jul 2013
    Location
    Vitoria , Spain
    Posts
    128

    Default

    Tomorrow more work...







    I DRIVE, HE GUIDE ME

    -FOOTBALL +RACES

    http://euskoscalecrawler.foroactivo.com/

  5. #5
    Join Date
    Jul 2013
    Location
    Vitoria , Spain
    Posts
    128

    Default




    I DRIVE, HE GUIDE ME

    -FOOTBALL +RACES

    http://euskoscalecrawler.foroactivo.com/

  6. #6
    Join Date
    Dec 2008
    Location
    Vitoria-gasteiz Spain
    Posts
    221

    Default

    Great job done , nice Hilux . Pics and videos fantastic
    [IMG]http://i705.photobucket.com/albums/w...Sig_Silver.jpg[/IMG]Greetings Udo

    Sorry for english it is horrible

  7. #7
    Join Date
    Jul 2013
    Location
    Vitoria , Spain
    Posts
    128

    Default

    Thanks Udo !!!!

    Saturday photos and videos
















    I DRIVE, HE GUIDE ME

    -FOOTBALL +RACES

    http://euskoscalecrawler.foroactivo.com/

  8. #8
    Join Date
    Jul 2013
    Location
    Vitoria , Spain
    Posts
    128

    Default

    now yes hehehe



    two photo of saturday inthe rocks

    I DRIVE, HE GUIDE ME

    -FOOTBALL +RACES

    http://euskoscalecrawler.foroactivo.com/

  9. #9
    Join Date
    Jul 2013
    Location
    Vitoria , Spain
    Posts
    128

    Default

    Finally going to have the hilux driver ...
    Fronted with this:

    And this outfit:


    And ... since I got on order, I order a spare spool

    I have not found appropriate to spend $ 10 more to buy coil ... so go to spare ...

    and some goodies ....

    I DRIVE, HE GUIDE ME

    -FOOTBALL +RACES

    http://euskoscalecrawler.foroactivo.com/

  10. #10
    Join Date
    Dec 2008
    Location
    Vitoria-gasteiz Spain
    Posts
    221

    Default

    Finally it would be complete with a driver
    [IMG]http://i705.photobucket.com/albums/w...Sig_Silver.jpg[/IMG]Greetings Udo

    Sorry for english it is horrible

  11. #11
    Join Date
    Jul 2013
    Location
    Vitoria , Spain
    Posts
    128

    Default

    for now it is what it is;


    We sprocket teeth with past and serrated crown ... a blight will only see the gray color of the fat is due to the chip .. mia mother ...

    the new accords better with what washers to make sure they play well with each other ... but I do but what you say it is manufacturing defect ... because almost a similar plea broke the cvd ...

    I have one thing clear. The following inversion about k44 ...

    I sent an email to Martin RcModelex is to buy it and who has sent me Directly to RC4WD, no problem, but an ugly detail by hand, since I have not bought .... if I buy audi at the dealership and I 'm not going to fault audi Spain where I go to dealership buy it .... what fun here ... that have washed hands .... Immediately
    I DRIVE, HE GUIDE ME

    -FOOTBALL +RACES

    http://euskoscalecrawler.foroactivo.com/

  12. #12
    Join Date
    Jul 2013
    Location
    Vitoria , Spain
    Posts
    128

    Default

    a shame, I say nothing more ...

    I you can delete the link and all ...

    agur
    I DRIVE, HE GUIDE ME

    -FOOTBALL +RACES

    http://euskoscalecrawler.foroactivo.com/

  13. #13
    Join Date
    Jul 2013
    Location
    Vitoria , Spain
    Posts
    128

    Default

    Ver "Yota axle rc4wd cases fabrication error solution 1" en YouTube - https://www.youtube.com/watch?v=jgeh...e_gdata_player

    Ver "Yota axle rc4wd fabrication error solution 2" en YouTube - https://www.youtube.com/watch?v=R5gy...e_gdata_player
    I DRIVE, HE GUIDE ME

    -FOOTBALL +RACES

    http://euskoscalecrawler.foroactivo.com/

  14. #14
    Join Date
    Jul 2013
    Location
    Vitoria , Spain
    Posts
    128

    Default

    this is the answer :

    Hello,

    Thanks for the video.

    The axles come pre shimmed from the factory. We always recommend for anyone to shim them when they arrive though.

    Tom

    where is this info ???

    The Ultimate Scale 1.9 Yota Cast Axles (Front)

    The most scale and complex axle on the market just become a lot more affortable! Extremly scale to the smallest details, such as innovative round knuckles (just like the real thing), lower mounts (let shocks be mounted front or back) and compact offset pumpkin.


    Specifications:

    Die Cast light weight metal housing
    Hardened steel spool gears
    5mm axle output shaft
    Full ball bearings
    Powdercated in black
    Width: 180mm/7.09inch
    Engineered by Fracture in New Zealand
    Manufactured by RC4WD
    Designed for 1:10 scale truck!
    Hex to Hex Width: 179mm / 7.04"
    Pin to Pin Width: 168mm / 6.61"
    Pumpkin Height: 36.2mm /1.42 "
    Leaf Mount Width: 79mm / 3.11"
    Gear Ratio: 2.67:1
    Output Shaft OD: 5mm / 0.19"
    Weight: 166g /5.85oz

    The actual product:

    http://www.beadlok.com/product/images/626/Z-A0058GG.jpg

    What's Included:

    1x The Ultimate Scale Yota Cast Axle Housing (front)
    2x Cast knuckles
    1x Steel axle
    1x Tracgear yota spool gear (Tracgear)
    2x 12mm steel wheel hex
    Complete hardwares and bearings

    Replacement Parts:

    Top and Bottom Axle case replacement (Z-A0078)
    Gear set (Z-S0027)
    Front Axle Shafts (Z-S0060)
    Third Member (Z-S0616)
    Steering Knuckles (Z-S0636)
    Replacement Hardware (Z-S0659)

    Optional Parts & Upgrade:

    Ultimate 4 links mount (Z-S0133) (4mm spacer needed)
    Wheel Widener (Z-S0407)
    Yota XVD axle (Z-S0342)
    4 links mounts (Z-S0133)
    Steering kit (Z-S0148)
    U bolt kit (Z-S0068)
    Axle shock mount (Z-S0221)
    Straight replacement axle (Z-S0061)
    Yota Ultimate Scale Cast Straight Axle (Rear) (Z-A0061)
    Yota Ultimate Scale Cast Straight Silver Axle (Rear) (Z-A0013)

    What is the difference between this and billet Yota axles?

    In terms of strength, cast version is about 85% in terms of strength of the billet version. All internals parts are the same as well.
    Notes:

    You can fit this axle onto the New Tamiya Bruiser with (Z-S0221) and (Z-S0518)
    Fits Trail Finder 2 Truck Kit w/Mojave Body Set (Z-K0042)
    Same type Front Yota Axle (Silver) (Z-A0019)
    I DRIVE, HE GUIDE ME

    -FOOTBALL +RACES

    http://euskoscalecrawler.foroactivo.com/

  15. #15
    Join Date
    Jul 2013
    Location
    Vitoria , Spain
    Posts
    128

    Default

    We will beat back angle without shortening the body overhang that long i like ...

    first picture with the body only cut


    Here we see how I want to make but are superfluous sleepers going in two pieces ...


    here and removed the bars ... I go hard iron ... not you become an idea ... now refine the cut and everything else to prepare to cut the chassis and resoldarlos this week but more up ... say bmcortare the last 3cm more less chassis along with the remains of the bumper cross me and a buddy welded up more (which makes me a tig favorazo) ...


    so it has to be

    I DRIVE, HE GUIDE ME

    -FOOTBALL +RACES

    http://euskoscalecrawler.foroactivo.com/

  16. #16
    Join Date
    Jul 2013
    Location
    Vitoria , Spain
    Posts
    128

    Default

    Now this soldier, this afternoon sanding and painting ...

    So ... buf is outside, better than I expected ....
    I DRIVE, HE GUIDE ME

    -FOOTBALL +RACES

    http://euskoscalecrawler.foroactivo.com/

  17. #17
    Join Date
    Apr 2012
    Location
    Southern Germany - Karlsruhe
    Posts
    311

    Default

    Good idea - tell Martin about so he can modify his chassis.
    [SIGPIC][/SIGPIC]
    In the end though, it all comes down to stick time...

  18. #18
    Join Date
    Jul 2013
    Location
    Vitoria , Spain
    Posts
    128

    Default

    I thank you mate!

    if you want to copy the idea, but did not inform anyone, especially people who do not care about customers ...
    I DRIVE, HE GUIDE ME

    -FOOTBALL +RACES

    http://euskoscalecrawler.foroactivo.com/

  19. #19
    Join Date
    Jul 2013
    Location
    Vitoria , Spain
    Posts
    128

  20. #20
    Join Date
    Dec 2008
    Location
    Vitoria-gasteiz Spain
    Posts
    221

    Default

    very cool i like your modifications .

    Alucinante Alberto me gusta como va
    [IMG]http://i705.photobucket.com/albums/w...Sig_Silver.jpg[/IMG]Greetings Udo

    Sorry for english it is horrible

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •