Announcement

Collapse
No announcement yet.

ARB Hilux

Collapse
X
  • Filter
  • Time
  • Show
Clear All
new posts

  • ARB Hilux

    !Hi !
    this is my new project .
    Trailfinder body
    modelex chasis
    gelande 2 wheel
    proline super swamper
    combo robitronic 21.5 sensor
    gmade piggyback shock regulable
    The other part come in a few days...





    Today the body meets chasis....





    Now waiting for more parts...
    today lights.. only with led 4 . For not more cables and holes for cables...



    today work , mount links and axles greased and xvc converted , hpi unit with motor and suspension gmade piggyback...
    for tomorrow mirrors ultimate rear suspension adjust






    Last mods...






    Thanks !





    Last edited by FREEDOM83; 07-28-2014, 08:01 AM.
    http://euskoscalecrawler.foroactivo.com/forum

    sigpic

  • #2
    Then I saw who was walking tricycles and insitu clearing and initially thought it was the pin rim mkrarlo but saw that it was good inside .... I is successfully broken the bearing pin ....
    remove the entire shaft and opening saw this:



    was all mounted right just gave too shift from emi and seems to heal him to turn over the account pulled the bearing out ... nothing less than 1mm but slowly over 8 hours of use that will have you see the result ....
    I initially ... I put the bearings of series and continue with the route but at the end of bearing take full group holding the same side of the shield was shattered miss ... neither will we no picture ... hehehehe
    nothing this morning I went for bearings here to shop Arizti bearings and good 3 euros each but I have caught pa is a special measure and was not valian which already had before ....



    and you see in the picture what today has come to me .... a trail rider rc4wd love handles and also rc4wd led bar ... asked all rcbitz .... this afternoon I have more work ... jejejee and this week also came innerspring cushions for back ... by the way on Saturday in the 15 minutes I could walk and test the spring issue and do not want to remove them ... just make a couple of adjustments ...

    Yesterday I started assembling the bearings of series and take to regrease and resets everything better
    and this morning I put the wheels ....
    First narrow blue rings rc4wd to put the swamper proline



    and after a few hours of work ..



    I have also left the bar LED placed



    and here with Their tires



    LIGHT TEST



    This afternoon mess! Yeah!


    !Mounted !




    LITTLE ACCIDENT...
    http://euskoscalecrawler.foroactivo.com/forum

    sigpic

    Comment


    • #3
      Now yess . Finished for the moment...

      Pitbull growler 1.55 arrived !

      comparision with swampers

      Here the rims for view why i can mount 1.55 tire in 1.9 rims

      mounted

      Hilux finished with new tires and new rubber mudflaps



      little boy repair and new color for hilux...



      http://euskoscalecrawler.foroactivo.com/forum

      sigpic

      Comment


      • #4
        Tomorrow more work...







        http://euskoscalecrawler.foroactivo.com/forum

        sigpic

        Comment


        • #5



          http://euskoscalecrawler.foroactivo.com/forum

          sigpic

          Comment


          • #6
            Great job done , nice Hilux . Pics and videos fantastic
            http://<a href="http://s705.photobuc...er.jpg</a></a>Greetings Udo

            Sorry for english it is horrible

            Comment


            • #7
              Thanks Udo !!!!

              Saturday photos and videos
















              http://euskoscalecrawler.foroactivo.com/forum

              sigpic

              Comment


              • #8
                now yes hehehe



                two photo of saturday inthe rocks

                http://euskoscalecrawler.foroactivo.com/forum

                sigpic

                Comment


                • #9
                  Finally going to have the hilux driver ...
                  Fronted with this:

                  And this outfit:


                  And ... since I got on order, I order a spare spool

                  I have not found appropriate to spend $ 10 more to buy coil ... so go to spare ...

                  and some goodies ....

                  http://euskoscalecrawler.foroactivo.com/forum

                  sigpic

                  Comment


                  • #10
                    Finally it would be complete with a driver
                    http://<a href="http://s705.photobuc...er.jpg</a></a>Greetings Udo

                    Sorry for english it is horrible

                    Comment


                    • #11
                      for now it is what it is;


                      We sprocket teeth with past and serrated crown ... a blight will only see the gray color of the fat is due to the chip .. mia mother ...

                      the new accords better with what washers to make sure they play well with each other ... but I do but what you say it is manufacturing defect ... because almost a similar plea broke the cvd ...

                      I have one thing clear. The following inversion about k44 ...

                      I sent an email to Martin RcModelex is to buy it and who has sent me Directly to RC4WD, no problem, but an ugly detail by hand, since I have not bought .... if I buy audi at the dealership and I 'm not going to fault audi Spain where I go to dealership buy it .... what fun here ... that have washed hands .... Immediately
                      http://euskoscalecrawler.foroactivo.com/forum

                      sigpic

                      Comment


                      • #12
                        a shame, I say nothing more ...

                        I you can delete the link and all ...

                        agur
                        http://euskoscalecrawler.foroactivo.com/forum

                        sigpic

                        Comment


                        • #13
                          Ver "Yota axle rc4wd cases fabrication error solution 1" en YouTube - https://www.youtube.com/watch?v=jgeh...e_gdata_player

                          Ver "Yota axle rc4wd fabrication error solution 2" en YouTube - https://www.youtube.com/watch?v=R5gy...e_gdata_player
                          http://euskoscalecrawler.foroactivo.com/forum

                          sigpic

                          Comment


                          • #14
                            this is the answer :
                            Last edited by FREEDOM83; 02-22-2018, 04:34 AM.
                            http://euskoscalecrawler.foroactivo.com/forum

                            sigpic

                            Comment


                            • #15
                              We will beat back angle without shortening the body overhang that long i like ...

                              first picture with the body only cut


                              Here we see how I want to make but are superfluous sleepers going in two pieces ...


                              here and removed the bars ... I go hard iron ... not you become an idea ... now refine the cut and everything else to prepare to cut the chassis and resoldarlos this week but more up ... say bmcortare the last 3cm more less chassis along with the remains of the bumper cross me and a buddy welded up more (which makes me a tig favorazo) ...


                              so it has to be

                              http://euskoscalecrawler.foroactivo.com/forum

                              sigpic

                              Comment

                              Working...
                              X